Huggies Gold Earrings

Most listings quote the outer diameter, which is the measurement across the whole earring including the tube. That is the figure that matches what the photograph shows and the one used for comparison between designs.

The inner diameter is the opening the lobe passes through, and it is always smaller by twice the gauge. On a heavy-gauge design the two figures can differ by a third or more of the stated size.

Where a listing gives both figures, use the inner one to judge whether the earring will close comfortably, and the outer one to judge how large it will appear once it is in.

It should hold its position without being pressed against the tissue. A correctly sized huggie closes without resistance and then stays where it is put rather than swinging or rotating.

If the closure has to be forced, or the lobe is compressed when the earring is shut, the inner diameter is too small for that ear and a wider one is the answer rather than a lighter gauge.

A huggie that swings freely and turns during the day is oversized for the piercing, which is comfortable but loses the close-set look the style is bought for.

Gauge here refers to the thickness of the tube measured across its section, given in millimetres. It describes how substantial the ring of metal is, not how wide the earring is overall.

A larger gauge makes the earring read as heavier and more solid, and it reduces the inner opening at any given outer diameter, so the fit tightens as the gauge goes up.

Gauge is also the measurement worth keeping constant when several huggies are worn together, since consistent thickness is what makes a run of earrings look like a set.

The closure works by a shaped tip passing a detent or seating into a notch, and the small arm carrying that tip has to flex slightly every time. Over many openings the metal loses a little of its spring and the click becomes softer.

A second possibility is wear at the hinge itself. If the pin and its seat have developed play, the two halves no longer meet squarely and the closure cannot seat properly even though nothing is broken.

Either condition is a bench job rather than grounds for replacement. A jeweller can adjust the arm that carries the closure, or fit a new pin through the hinge, and neither repair alters how the earring looks.

In most cases yes. The usual repair is to adjust the angle of the arm that carries the closure so that it engages the detent more firmly, which restores the click without altering the shape of the earring.

Where the hinge knuckle has worn, the pin can be replaced with a slightly larger one, which takes up the play. This is routine work on gold and does not change the appearance.

What is worth avoiding is squeezing the earring shut harder to compensate. That flexes the tube itself rather than the closure and moves the problem rather than fixing it.

Many people wear them there, and the close-set profile is part of the appeal. The constraint is dimensional rather than stylistic: cartilage does not compress, so the inner diameter has to clear the tissue rather than pressing it.

Cartilage piercings are often made at a heavier gauge than lobe piercings. The tube has to match the channel that is already there, so the gauge figure matters as much as the diameter.

A piercer can say what gauge a particular piercing was made at, and what inner diameter sits comfortably in it. That turns the question from guesswork into two figures to shop against.

That depends entirely on how many piercings there are and how far apart they sit. The practical limit is spacing: two huggies whose outer edges meet will push against each other and both will sit crooked.

A useful check is to add the two outer diameters and compare that with the distance between the piercings. If the sum is larger, one of the two needs to be a smaller diameter.

Alternating huggies with flat-sitting studs relieves the crowding, because a stud occupies almost no space in front of the ear and leaves the projecting hoops room to sit without touching one another.

Because the earring opens on a hinge rather than being threaded through the piercing. The two halves separate at a known point, so the tip can be guided into the channel from behind with one hand rather than aimed blind.

There is also nothing to drop. The closure is part of the earring itself, so no separate back has to be held, aligned and pushed on.

The short travel helps as well: a small hoop moves the tip only a few millimetres from open to closed, which is easier to control by feel than a long arc.

Less than most earring styles, because the whole point of the design is that it sits tight to the lobe with no projecting arc for fabric to pass under. There is no drop and no free-hanging element.

Where snagging does happen it is usually at a stone setting on the front face, particularly where prongs stand proud of the surface. Bezel and flush-set designs sit smoother.

The join line at the closure can also catch if the two halves are no longer meeting cleanly, which is a sign the closure wants adjusting.

It sits further out from the lobe, yes. Gauge is added to both the inside and the outside of the ring, so a heavier tube stands proportionally further proud of the ear at the front and takes up more of the opening at the back.

That changes the look substantially. A fine-gauge huggie reads as a line drawn round the lobe; a heavy-gauge one reads as a band of metal with visible depth.

It also changes how the earring behaves in wear. A wider tube makes contact with the lobe across a larger area and moves less, so the design tends to stay in whatever position it is set.